The Tilting Pan Filter belongs to the top feed group and has found its main application in the phosphoric acid industry and, to some extent, in the washing of phosphate rock. As already mentioned in the Horizontal Belt Filters section there was a traditional rivalry over the years between the Pan and Belt Filter which now, owing to the substantial progress in rubber technology, swings in the favor of the later.But the Suita filter cloth can still be fitted in these filters.

The operation of Tilting Pan Filters is based on a series of horizontal independent trapezoidal pans mounted on a circular supporting structure that rotates under vacuum during the filtration cycle and invert under blow to discharge the cake. During filtration the cake may be washed counter-currently, generally in three stages, while the mother and wash filtrates are flowing to separate vacuum receivers. After the final drying portion of the cycle the cake is discharged dry for piling or sluiced as a slurry for disposal to ponds. Following cake discharge the pans pass over radial manifolds with high impact jets that clean the cloth and dislodge any cake leftovers that remained on the pan's surface.

 

At the last stage before relevelling, suction is applied to evacuate the wash water that accumulates inside the pan, and at the same time it dries the cloth to avoid dilution of the mother filtrate. Since during this stage air passes freely through the exposed cloth, applying suction with the main vacuum pump will cause a loss of vacuum to the entire system, hence, an auxiliary small vacuum pump is incorporated to separate between the vacuum zones.

 

Feed Box Pan-Filtering Pan-Discharging Cake Hopper Main Valve Vacuum Hoses Walkway Pan Bearings Outer Support Rim Inner Support Rim     To view the components move     mouse pointer over the menu

The main valve, that is also called distributor, controls the cycle segments with bridges that open and close the port of each pan as it passes from high vacuum through cake blow-off to low vacuum. Compartments within the valve separate the various zones to ensure that the separation is sharp and no mixing of mother, strong, middle and weak filtrates occurs during the cycle.

To speed up the evacuation of the various filtrates there are valves with two bridge circles, one for the main stream and the another that opens to atmosphere and purges the pan below the deck just before entering a new zone.

The speed of rotation determines the cycle time and this, being an important design parameter, is limited mechanically by the mass inertia of the swinging pan and its wet cake load at the point of discharge. Typical cycle times for Pan Filters are 2½ to 3 minutes depending on the size of the filter and the design of the peripheral cam that controls the tilting velocity.

Pan Filters are available for dry or wet cake discharge depending on the method of disposal. The discharge zone for dry discharge consists of two chutes, one for the dry cake and the second for cloth washing. The zone for wet discharge has one chute only in which the cake is sluiced and then the cloth is washed. Dry cake discharge consumes about 3-4% more effective filtration area than the wet discharge so this should be taken in account while calculating the required area.

The Tilting Pan Filter is constructed from the following subassemblies:

• Trapezoidal pans with sloping bottoms for fast evacuation of filtrates and each fitted with a roller arm assembly that tilts and relevels the pan as it passes trough the inverting track. Special circumferential fasteners enable the quick replacement of filter cloths.
• A central valve with bridge setting to control the various zones throughout the filtration cycle, and in some instances, two bridge circles with the second serving to purge the pan. The valve has internal compartments for the mother and wash filtrates.
• A feed and wash boxes that may be set in a slight slope so that the distribution over the trapezoidal surface will be proportional to the pan's area. This will ensure that the formed cake is even in thickness and that the applied wash liquids are distributed evenly.
• A structure that rotates over rollers, supports the pans and is fitted with a toothed rim that drives the filter.

If you want more filtration knowledge, pls kindly drop at www.be-pure.net for closer learning.

 

Selection Criteria

 

As mentioned in an earlier discussion the Pan Filters have been set aside once the rubber technology enabled the manufacture Horizontal Belt Filters with large filtration areas. Presently there are no outstanding features to prefer a Tilting Pan Filter over a Belt Filter although many of them are in extensive use.